Materials Included In Kit

Additional Materials Required

Prelab Preparation

To prepare potassium thiocyanate, KSCN, 0.002 M, 500 mL for the Introductory Activity: Measure 10.0 mL of 0.10 M KSCNsolution in a 10-mL graduated cylinder. Fill a 500-mL volumetric flask one-third to one-half full with distilled or deionized water. Pour the 10.0 mL of KSCN into the flask. Swirl to mix. Fill the flask to the mark with distilled water. Stopper the flask and mix well by inverting several times prior to dispensing.

Safety Precautions

Cobalt chloride solution is a flammable liquid and moderately toxic by ingestion. Iron(III) nitrate solution may be a skin and body tissue irritant. Concentrated ammonia (ammonium hydroxide) solution is severely corrosive and toxic by inhalation and ingestion. Work with concentrated ammonium hydroxide only in a fume hood. Hydrochloric acid solution is toxic by ingestion and inhalation and is corrosive to skin and eyes. Keep sodium carbonate and citric acid on hand to neutralize any acid or base spills, respectively, in the lab. Dilute hydrochloric acid and sodium hydroxide solutions are skin and eye irritants. Potassium thiocyanate is toxic by ingestion and emits a toxic gas if strongly heated—do not heat this solution and do not add acid. Sodium phosphate monobasic is moderately toxic by ingestion. Avoid contact of all chemicals with eyes and skin. Wear chemical splash goggles, chemical-resistant gloves and a chemical-resistant apron. Remind students to wash their hands thoroughly with soap and water before leaving the laboratory. Please review current Safety Data Sheets for additional safety, handling and disposal information.

Disposal

Please consult your current Flinn Scientific Catalog/Reference Manual for general guidelines and specific procedures, and review all federal, state and local regulations that may apply, before proceeding. Cobalt-containing solutions from Activity C may be combined and handled according to Flinn Suggested Disposal Method #27f. The end solution of Activity E may be slightly acidic and may be neutralized according to Flinn Suggested Disposal Method #24b. The copper–ammonia solutions from Activity B may be combined and handled according to Flinn Suggested Disposal Method #10. Solutions from the Introductory Activity and Activities A and D may be rinsed down the drain with excess water according to Flinn Suggested Disposal Method #26b.

Lab Hints

• The Introductory Activity contains enough materials for 12 groups of students to work at the same time.
• The guided-inquiry activities contain enough materials for two lab stations to be set up throughout the lab. For best results, set up two stations for each activity at the same lab table. This will allow two groups of students to work on each activity. An optional sixth activity can be set up following the instructions in the Teaching Tips. The activities may be completed in any order and students should only need 10 minutes per station.
• Activity B must be completed in a fume hood. Concentrated ammonia vapors are extremely irritating, especially to the eyes.
• An optional sixth activity station may be used to model equilibrium using small objects such as pennies, paper clips or plastic discs. Student groups may be given 60 objects with which to start. In the reaction, one-third of the total reactants are converted into products; one-fourth of all products are converted into reactants. After each round of reaction, students should count the total number of reactants and products. These amounts can be graphed to model equilibrium amounts of reactants and products. Students can investigate how the amounts of reactants and products change if reactants or products are added at equilibrium, if the starting amount(s) is different, and if reactants or products are removed from equilibrium.
• In Activity B, the solid formed initially in the reaction between copper(II) ions and ammonia is copper(II) hydroxide. The concentrated ammonia solution produces hydroxide ions that bond with the Cu²⁺ ions as shown in the following equation: Cu²⁺(aq) + 2OH^-(aq) → Cu(OH)₂(s). Copper(II) hydroxide is insoluble. Adding excess ammonia is necessary to displace the OH^– ions to create the dark blue complex ion, [Cu(NH₃)₄]²⁺.
• In Activity C, the most common misconception students make regarding the shift in equilibrium when water is added is that the concentration of water increases. The concentration of water is constant around 55 M, so the addition of more water does not affect its concentration. However, the addition of water dilutes the other species in the solution. The concentrations of the chloride ion (Cl^–), [CoCl₄]^2– ion, and [Co(H₂O)₆]²⁺ ion all decrease. The rates of the forward and reverse reactions are affected, but not equally. The best way to explain the shift in equilibrium is through a comparison between Q, the reaction quotient, and K_eq, the equilibrium constant.
• The activity of hemoglobin, the main oxygen-binding protein in red blood cells, illustrates an application of complex-ion equilibrium. Hemoglobin (Hb) contains four iron(II) ions that bind to oxygen molecules. This is a reversible reaction, since the hemoglobin must be able to release the oxygen molecules in cells and body tissues (Equation 7).
  {13835_Hints_Equation_7}
• At high altitudes, where the concentration of oxygen is lower, the equilibrium shown in Equation 7 is shifted in the reverse direction. Less bound oxygen is therefore available in the bloodstream to be transported to the cells. The physical symptoms of the reduced oxygen availability are fatigue and dizziness. The human body, however, is marvelous in its adaptability. People who live or train at high altitudes compensate for the reduced oxygen supply by synthesizing more red blood cells. Increasing the concentration of hemoglobin increases the rate of the forward reaction and thus increases the amount of available oxygen.
• Most textbooks use Le Chatelier’s Principle to predict and explain the effects of both concentration and temperature. Strictly speaking, however, the two effects are different, in that changes in concentration affect the position of equilibrium while changes in temperature affect the value of the equilibrium constant. At a given temperature, there are an infinite number of possible equilibrium positions, but only a single equilibrium constant value.
• The effect of acid on the solubility equilibrium of magnesium hydroxide can be used to illustrate the action and effectiveness of Milk of Magnesia, a popular antacid. Milk of Magnesia is a suspension of solid magnesium hydroxide in water. The suspension dissolves as required in the stomach to combat excess acidity.
• The equilibrium constant, K_eq, of the iron(III) thiocyanate complex ion (FeSCN²⁺) can be determined through colorimetric or spectrophotometric analysis. The Flinn laboratory kit, Determination of K_eq for FeSCN²⁺ (Catalog No. AP7952), may be used to reinforce Le Chatelier’s principle as well as show the change in equilibrium position based on the concentration of the products and reactants.

Further Extensions

Opportunities for Undergraduate Research

The equilibrium systems studied in this activity lend themselves toward use in colorful displays. In small groups or as a cooperative class activity, plan how a rainbow-colored display can be made using the equilibrium systems studied in this activity. Develop procedures to incorporate each system into the display.

Answers to Prelab Questions

1. Iodine (I₂) is only sparingly soluble in water (Equation 3).
   {13835_PreLab_Equation_3}
   In the presence of potassium iodide, a source of iodide (I^–) ions, iodine reacts to form triiodide (I₃^–) ions (Equation 4).
   {13835_PreLab_Equation_4}
   Use Le Chatelier’s principle to explain why the solubility of iodine in water increases as the concentration of potassium iodide increases.

   Increasing the concentration of the iodide ions creates a “stress.” According to Le Chatelier’s principle, the system will react in a way that tends to reduce the stress. The reaction shown in Equation 4 will shift in the forward direction, to make more triiodide ions and consume some of the added iodide with aqueous iodine. This, in turn, also causes more solid iodine to dissolve in the solution. Note: Not all of the excess reagent is consumed when the equilibrium shifts. This is a common misconception. The equilibrium is re-established with higher concentrations of all substances in solution.

2. Although both N₂ and O₂ are naturally present in the air we breathe, high levels of NO and NO₂ in the atmosphere occur mainly in regions with large automobile or power plant emissions. The equilibrium constant for the reaction of N₂ and O₂ to give NO is very small. The reaction is, however, highly endothermic, with a heat of reaction equal to +180 kJ (Equation 5).
   {13835_PreLab_Equation_5}
   1. Use Le Chatelier’s principle to explain why the concentration of NO at equilibrium increases when the reaction takes place at higher temperatures.

      According to Le Chatelier’s principle, increasing the temperature shifts the equilibrium in the direction of the reaction in which heat is absorbed. Therefore, the reaction shifts to increase the forward reaction, in favor of the production of NO.

   2. Use Le Chatelier’s principle to predict whether the concentration of NO at equilibrium should increase when the reaction takes place at high pressures.

      According to Le Chatelier’s principle, increasing the pressure should not affect the position of the equilibrium for the reaction. Since there are an equal number of gas molecules on each side of the equation, an increase in pressure will not favor the forward or reverse reactions. Note to instructors: There is also a kinetic argument that can be made. Reactions of gases generally occur much faster at elevated temperatures and pressures.

Sample Data

Introductory Activity

Part A. Observations

Part B. Observations Guided-Inquiry Activities A–E

Activity A. Acid–Base Indicator Equilibrium
Reactions Activity B. Formation of a Copper Complex Ion
Reactions Activity C. Formation of Cobalt Complex Ions
Reactions Activity D. Solubility of Carbon Dioxide
Reactions Activity E. Solubility of Magnesium Hydroxide
Reactions

Answers to Questions

Introductory Activity 

1. Write the chemical equation for the reversible reaction of iron(III) ions with thiocyanate ions. Use the information in the data table to write the color of each reactant and product underneath its formula.
   {13835_Answers_Reaction_1}
2. How did the color of the solution change when additional reactant—either Fe(NO₃)₃ or KSCN—was added? Explain the observed color changes by discussing the rates of the forward and reverse reactions, as well as the concentrations of products and reactants.

   Adding Fe(NO₃)₃ or KSCN produced the same effect. The color of the solution changed from orange to dark red. The dark red color indicates that the amount of product, FeSCN²⁺, increased. Adding more reactant(s) to an equilibrium system increases the concentration of the reactant(s). This increases the rate of the forward reaction to produce more product and increases the concentration of the product.

3. In step 6, KNO₃ was added to the solution. How did the color of the solution change in Part A when KNO₃ was added? Explain this observation.

   Adding KNO₃ to the solution had no effect on the observed color. This indicates that neither the potassium nor nitrate ions are involved in the equilibrium reaction. This supports the net ionic equation for the equilibrium reaction that involves only the iron(III) and thiocyanate ions.

4. In step 7, H₂PO₄^– ions combined with iron(III) ions and removed them from solution. How did the color of the solution change in Part A when NaH₂PO₄ was added? Explain the observed color change by discussing the rates of the forward and reverse reactions, as well as the concentrations of the products and reactants.

   Adding sodium phosphate decolorized the solution—the red color disappeared and the solution turned light yellow and cloudy. The amount of product, FeSCN²⁺, decreased because of the loss of the red color. This indicates that one of the reactant concentrations decreased due to the addition of the H₂PO₄^– ion. Therefore, the rate of the reverse reaction was increased to form more reactants. Note to instructors: The reaction that occurs in step 7 is the formation of another iron(III) complex ion. The Fe³⁺ reacts with H₂PO₄^– to produce FeH₂PO₄²⁺, a colorless ion. When the reverse reaction is favored, the H₂PO₄^– ion reacts with the newly formed Fe³⁺ ions, continuing the cycle until there are very few Fe³⁺ ions left in solution.

5. How did the color of the solution change when Fe³⁺ ions were added in step 9 and SCN^– ions were added in step 10? How do these observations demonstrate that both reactant ions are present at equilibrium?

   Adding either reactant caused the solution to change color to red (Fe³⁺) or orange (SCN^–), indicating an increase in the amount of product. Since additional product formed when both reactants were added independently, the other reactant must be present in the solution.

6. How did the color of the solution change in Part B when it was cooled (step 15) or heated (step 16)? How do these results demonstrate that the reaction does indeed occur in both the forward and reverse directions?

   Opposite color changes were observed when the solution was cooled or heated. The solution changed from an orange color to a redorange color when it was cooled. The solution then changed to a lighter orange color when it was heated. These results indicate that the reaction can “go both ways.” The solution must contain equilibrium concentrations of both reactants and products. When the solution was cooled, the concentration of the red product increased, indicating the rate of the forward reaction was increased. When the solution was heated, the concentration of red product decreased, indicating the rate of the reverse reaction was increased.

7. Based on the color changes observed when the solution was cooled and heated, is the reaction between iron(III) ions and thiocyanate ions exothermic or endothermic? Write the Heat term on the correct side of the equation from Question 1.

   Based on the observations from steps 15 and 16, the reaction between iron(III) ions and thiocyanate ions is exothermic.

   {13835_Answers_Reaction_2}

Post-Laboratory Review Questions
When a chemical is manufactured, chemists and chemical engineers choose conditions that will favor the production of the desired product as much as possible. They want the forward reaction to occur more quickly than the reverse reaction. In the early 20th century, Fritz Haber developed a process for the large-scale production of of ammonia from its constituent elements. Some of his results are summarized in the following chart.

*Each experiment began with a stoichiometric mixture of H₂ and N₂.

1. Write the balanced chemical equation, including the heat term, for the synthesis of ammonia from its constituent elements.
   {13835_Answers_Reaction_3}
2. Based on the results above, explain the effect of temperature on the equilibrium position of the reaction.

   When the pressure of the reaction was held constant, an increase in the temperature decreased the amount of ammonia at equilibrium. The reaction is exothermic. With an increase in the amount of heat, the rate of the reverse reaction increased to absorb the excess heat. Note that the value of K_eq depends on temperature.

3. Explain the effect of pressure on the equilibrium position of the reaction.

   When the temperature of the reaction is held constant, an increase in pressure increases the amount of ammonia formed at equilibrium. An increase in pressure on a gaseous equilibrium system will increase the rate of the reaction in the direction of the side with fewer moles of gases. In this case, the rate of the forward reaction is increased because the product side has two moles of gas (ammonia) while the reactant side has four moles of gas (hydrogen and nitrogen).

4. The optimal conditions to synthesize ammonia are high pressures and low temperatures. However, each factor comes with a drawback: high pressures require strong pipework and hardware, and at low temperatures the reaction is slow. In order to get high yields of ammonia at lower pressures and higher temperatures, ammonia is removed from the system as it is formed. Use Le Chatelier’s principle to explain why this is effective.

   Although the percent yield of ammonia is less at lower pressures and high temperatures, the amount of ammonia collected can be increased by constantly removing ammonia from the system as it is produced. This will increase the rate of the forward reaction because the concentration of ammonia will be reduced.

References

Zumdahl, S. et al. Chemistry, 5th ed; Massachusetts: Houghton Mifflin Company, 2000.

Introduction

Not all chemical reactions proceed to completion, that is, to give 100% yield of products. In fact, most chemical reactions are reversible, meaning they can go both ways. When the forward rate and reverse rate are equal, the system is at equilibrium. What happens when the equilibrium system is disturbed? Is there a way to predict and explain the effects of the disturbances?

Guided-Inquiry Design and Procedure
Using the procedure in the Introductory Activity as a guide, investigate the following chemical equilibrium systems A–E. Materials are provided for each activity—investigations are limited to those materials. A short procedure is provided to setup the initial conditions for each equilibrium system. For each activity, design a testing procedure to determine the color and appearance of both reactants and products and to investigate any effects of concentration, temperature and pressure.

Concepts

• Chemical equilibrium
• Exothermic and endothermic reactions
• Precipitation reactions
• Le Chatelier’s principle
• Acid–base reactions
• Gas solubility
• Complex-ion reactions

Background

In a closed system, any reversible reaction will eventually reach a point where the amounts of reactants and products do not change. This occurs when the rate of the forward reaction equals the rate of the reverse reaction. At this point, the system is said to be in a dynamic balance or dynamic equilibrium—the reactions are occurring but no observable changes can be measured. Chemical equilibrium can therefore be defined as the state where the concentrations of reactants and products remain constant with time. This does not mean the concentrations of reactants and products are equal. The forward and reverse reactions create an equal balance of opposing rates.

These ideas can be expressed mathematically in the form of the equilibrium constant. Consider the following general equation for a reversible chemical reaction:

The equilibrium constant, K_eq, for this general reaction is given by Equation 2, where the square brackets refer to the molar concentrations of the reactants and products at equilibrium. The equilibrium constant gets its name from the fact that for any reversible chemical reaction, the value of K_eq is a constant at a particular temperature. The concentrations of reactants and products at equilibrium vary, depending on the initial amounts of materials present. The special ratio of reactants and products described by K_eq is always the same, however, as long as the system has reached equilibrium and the temperature does not change.

Any change that is made to a system at equilibrium may be considered a stress—this includes adding or removing reagents, or changing the temperature or pressure. The rates of the forward and reverse reactions will change as a result until equilibrium is again established. Henry Le Chatelier published many studies of equilibrium systems. Le Chatelier’s principle predicts how equilibrium can be restored:

“If an equilibrium system is subjected to a stress, the system will react in such a way as to reduce the stress.”

Le Chatelier’s principle is a qualitative approach to predicting and interpreting shifts in equilibrium systems. A quantitative approach utilizes the K_eq of the reaction and the reaction quotient, Q. The reaction quotient is a snapshot of the concentrations of reactants and products at a particular time. Q is calculated using the same formula as K_eq (Equation 2). Depending on the instantaneous concentrations of reactants and products, Q and K_eq may differ or be the same. If Q and K_eq differ, the system is not at equilibrium and the rates of the forward and reverse reactions will change until Q = K_eq.

The effect of concentration on a system at equilibrium depends on whether the change in concentration is affecting a reactant or product species. In general when the concentration of a species is increased, the system will shift and increase the rate of the reaction that decreases the concentration of that species. If the concentration of a species is decreased, the system will shift and increase the rate of the reaction that increases the concentration of the species. For example, if the concentration of a reactant is increased, the rate of the forward reaction will increase because the forward reaction decreases the concentration of reactants.

The equilibrium constant for a reaction depends on or changes with temperature. The observable effect of temperature on a system at equilibrium depends on whether the reaction is endothermic (absorbs heat) or exothermic (produces heat). If a reaction is endothermic, heat appears on the reactant side in the chemical equation. Increasing the temperature of an endothermic reaction shifts the equilibrium in the forward direction, absorbing some of the excess energy and making more products. The opposite effect is observed for exothermic reactions. In the case of an exothermic reaction, heat appears on the product side in the chemical equation. Increasing the temperature of an exothermic reaction shifts the equilibrium in the reverse direction.

The effect of pressure on a gaseous system at equilibrium depends on the partial pressures of the gases and the stoichiometry of the reaction. A change in pressure of a gaseous system has the effect of altering the partial pressures of the gases, and is typically accomplished through changes in volume. An increase in volume results in an overall decrease in pressure. The system will respond in a way as to produce more gas molecules to fill the space. Thus, the reaction will shift towards the side with the greater number of moles of gas. If the volume of the container is decreased, the overall pressure will increase and the system will shift in the direction of the side with fewer number of moles of gas in order to decrease the pressure.

Experiment Overview

In this inquiry kit, six equilibrium systems will be investigated to gain a deeper understanding of equilibrium and Le Chatelier’s principle. An introductory activity guides you through the equilibrium achieved between iron(III) nitrate and potassium thiocyanate. Deliberate stresses are added to the system to cause the equilibrium to shift and the color to change. The procedure provides a model for guided-inquiry investigation of five additional equilibrium systems, which are set up as lab stations. The inquiry activities include an acid–base indicator, copper complex ion, cobalt complex ion, solubility of carbon dioxide and the solubility of magnesium hydroxide. The key to success in this lab is detailed notes and observations. The activity may be extended to create a rainbow-colored display using the equilibrium systems.

Guided-Inquiry Design and Procedure

Activity A. Acid–Base Indicator Equilibrium
An indicator is a dye that can gain or lose hydrogen ions to form substances that have different colors. For simplicity, the uncharged indicator molecule may be represented as HIn, and the anionic indicator molecule after the loss of a hydrogen ion may be written as In^–. Bromthymol blue will be used as the indicator in this activity.

Activity B. Formation of a Copper Complex Ion
An equilibrium system can be formed in a solution of copper(II) ions and ammonia. A copper–ammonia complex ion forms when the amount of ammonia in solution reaches a high enough concentration. Please note that ammonia (NH₃) is provided in the form of a concentrated solution in water, which is usually referred to as ammonium hydroxide (NH₄OH). These two names are interchangeable. The reaction of copper(II) ions with this solution should be written for convenience as Cu²⁺ + NH₃.

Activity C. Formation of Cobalt Complex Ions
When cobalt(II) chloride hexahydrate (CoCl₂•6H₂O) is dissolved in ethyl alcohol, three different solute species are present: Co²⁺ cations, Cl^– anions, and water molecules. These can react to form two different complex ions: Co(H₂O)₆²⁺, where the cobalt ion is surrounded by six water molecules, and CoCl₄^2–, in which the metal ion is surrounded by four chloride ions.

Activity D. Solubility of Carbon Dioxide
When carbon dioxide dissolves in water, it forms a weakly acidic solution due to the following reversible reaction:

The hydrogen ion concentration in solution depends on the amount of dissolved carbon dioxide. According to Henry’s law, the amount of gas dissolved in solution is proportional to the pressure of the gas above the solution.

Activity E. Solubility of Magnesium Hydroxide
The active ingredient in milk of magnesia, an over-the-counter antacid remedy, is magnesium hydroxide. Magnesium hydroxide forms a suspension in water due to its low solubility—0.0009 g/100 mL in cold water and 0.004 g/100 mL in hot water.

Materials

Prelab Questions

1. Iodine (I₂) is only sparingly soluble in water (Equation 3).
   {13835_PreLab_Equation_3}
   In the presence of potassium iodide, a source of iodide (I^-) ions, iodine reacts to form triiodide (I₃^–) ions (Equation 4).
   {13835_PreLab_Equation_4}
   Use Le Chatelier’s principle to explain why the solubility of iodine in water increases as the concentration of potassium iodide increases.
2. Although both N₂ and O₂ are naturally present in the air we breathe, high levels of NO and NO₂ in the atmosphere occur mainly in regions with large automobile or power plant emissions. The equilibrium constant for the reaction of N₂ and O₂ to give NO is very small. The reaction is highly endothermic, with a heat of reaction equal to +180 kJ (Equation 5).
   {13835_PreLab_Equation_5}
   1. Use Le Chatelier’s principle to explain why the concentration of NO at equilibrium increases when the reaction takes place at higher temperatures.
   2. Use Le Chatelier’s principle to predict whether the concentration of NO at equilibrium should increase when the reaction takes place at high pressures.

Safety Precautions

Cobalt chloride solution is a flammable liquid and moderately toxic by ingestion. Iron(III) nitrate solution may be a skin and body tissue irritant. Concentrated ammonia (ammonium hydroxide) solution is severely corrosive and toxic by inhalation and ingestion. Work with concentrated ammonium hydroxide only in a fume hood. Hydrochloric acid solution is toxic by ingestion and inhalation and is corrosive to skin and eyes. Dilute hydrochloric acid and sodium hydroxide solutions are skin and eye irritants. Potassium thiocyanate is toxic by ingestion and emits a toxic gas if strongly heated—do not heat this solution and do not add acid. Sodium phosphate monobasic is moderately toxic by ingestion. Avoid contact of all chemicals with eyes and skin. Wear chemical splash goggles, chemical-resistant gloves and a chemical-resistant apron. Wash hands thoroughly with soap and water before leaving the laboratory. Please follow all laboratory safety guidelines.

Procedure

Introductory Activity

Part A. Effect of Concentration

1. Prepare hot-water and ice-water baths: Fill a 250-mL beaker half full with tap water. Place it on a hot plate and heat to 65–70 °C for use in Part B. In a second 250-mL beaker, add water and ice to prepare an ice-water bath for use in Part B.
2. Using a 50-mL graduated cylinder, measure 20 mL of potassium thiocyanate solution and pour the solution into a Petri dish. Record the initial color and all color changes that occur throughout the investigation (Parts A and B).
3. Add 3 drops of iron(III) nitrate solution to different spots in the Petri dish. Swirl the solution until the color is uniform throughout.
4. Add ½ pea-size amount of potassium thiocyanate crystals in one spot. Wait 30 seconds and record any further changes to the solution. Swirl the solution to dissolve the crystals until the solution color becomes uniform throughout.
5. Add ½ pea-size amount of potassium nitrate crystals in one spot. Wait 30 seconds and record any further changes to the solution. Swirl the solution to dissolve the crystals until the solution color becomes uniform throughout.
6. Add ¼ pea-size amount of sodium phosphate monobasic crystals in one spot. Wait about 60 seconds and observe any changes to the solution.
7. Swirl the solution to dissolve the crystals. Record the solution color.
8. Add one drop of iron(III) nitrate solution in one spot off to the side. Do not stir. Record any color change.
9. Add a pea-size amount of potassium thiocyanate crystals in a different spot. Wait about 30 seconds and record any changes to the solution around the crystals.
10. Swirl the solution until it is uniform and keep the solution for use in Part B—Effect of Temperature.

Part B. Effect of Temperature

11. Label two clean, dry test tubes A and B, and place them in a test tube rack. Using a graduated Beral-type pipet, add about 10 mL of the complex-ion solution from Part A to each test tube. Test tube A will be the control for the experiment.
12. Place test tube B in the ice-water bath. After 3–5 minutes, remove the test tube from the ice bath using a test tube holder and compare the color of the solution to the control in test tube A. Record the color comparison.
13. Using a test tube holder, place test tube B in a hot-water bath at 65–70 °C. After 2–3 minutes, remove the test tube from the hot-water bath and compare the color of the solution to the control in test tube A. Record the color comparison.
14. Empty the contents of both test tubes and the Petri dish into the wash beaker provided. Rinse the glassware with distilled water.

Analyze the Results
Form a working group with other students and discuss the following questions.

1. Write the chemical equation for the reversible reaction of iron(III) ions with thiocyanate ions. Use the information in your data table to write the color of each reactant and product underneath its formula.
2. How did the color of the solution change when additional reactant—either Fe(NO₃)₃ or KSCN—was added? Explain the observed color changes by discussing the rates of the forward and reverse reactions, as well as the concentrations of products and reactants.
3. In step 6, KNO₃ was added to the solution. How did the color of the solution change in Part A when KNO₃ was added? Explain this observation.
4. In step 7, H₂PO₄^– ions combined with iron(III) ions and removed them from solution. How did the color of the solution change in Part A when NaH₂PO₄ was added? Explain the observed color change by discussing the rates of the forward and reverse reactions, as well as the concentrations of the products and reactants.
5. How did the color of the solution change when Fe³⁺ ions were added in step 9 and SCN^– ions were added in step 10? How do these observations demonstrate that both reactant ions are present at equilibrium?
6. How did the color of the solution change in Part B when it was cooled (step 15) or heated (step 16)? How do these results demonstrate that the reaction does indeed occur in both the forward and reverse directions?
7. Based on the color changes observed when the solution was cooled and heated, is the reaction between iron(III) ions and thiocyanate ions exothermic or endothermic? Write the Heat term on the correct side of the equation from Question 1.

Guided-Inquiry Design and Procedure

Activity A. Acid–Base Indicator Equilibrium
Initial conditions: Measure approximately 2 mL of distilled water and add to a test tube. Add 5 drops of 0.04% bromthymol blue. Swirl gently.

Activity B. Formation of a Copper Complex Ion
Initial conditions: Add approximately 5 mL of 0.2 M CuSO₄ to a test tube. In a fume hood, add the concentrated ammonium hydroxide solution dropwise.

Activity C. Formation of Cobalt Complex Ions
Initial conditions: Label three test tubes A–C and place them in a test tube rack. Using a graduated, Beral-type pipet, add about 2 mL of the cobalt chloride solution to each test tube A–C. Note: The exact volume is not important, but try to keep the volume of the solution approximately equal in each test tube.

Activity D. Solubility of Carbon Dioxide
Initial conditions: Obtain approximately 10 mL of fresh seltzer water in a 50-mL beaker. Add about 20 drops of 0.04% bromcresol green indicator. Swirl to mix the solution. Draw up about 10 mL of the seltzer/indicator solution into a 30-mL syringe. Seal the syringe by pushing a tip cap firmly onto its open end.

Activity E. Solubility of Magnesium Hydroxide
Initial conditions: Obtain 10 mL of the milk of magnesia solution. Add this to a 250-mL beaker. Add approximately 50 mL of distilled water. Add 5–10 drops of universal indicator solution. Swirl to mix the solution.

Analyze the Results for Activities A–E
Form a working group with other students to review and summarize each equilibrium system studied. Devise a way to clearly display the chemical reaction(s), procedural steps, observations and explanations for any and all color changes for each equilibrium system. The results for all indicators should include the pH range and color for each form of the indicator (HIn and In^–).

Student Worksheet PDF

13835_Student1.pdf